通風管道用橡膠接頭有什么要注意的嗎？

發布人：http://www.rdhw.com.cn   發布時間：2020-05-29 18:47:48

　　通風管道用橡膠接頭主要由三部分組成，內膠層是由力威自主合成的橡膠來制 作的橡膠球體，增強層是采用簾子布來作為橡膠接頭的添加物以增強橡膠接頭的彈性 及耐磨性能，連接部分可以是法蘭連接方式和套管連接方式，還有卡箍等多種連接方式可供選擇。有人咨詢問：橡膠軟接頭使用注意事項是什么？今天來介紹一下濟南通風管道橡膠軟接頭使用注意事項。

　　Rubber joints for ventilation pipes are mainly composed of three parts. The inner rubber layer is a rubber ball made of rubber synthesized by Liwei. The reinforcing layer uses cord cloth as the additive of rubber joints to enhance the elasticity and wear resistance of rubber joints. The connecting part can be made of flange connection and sleeve connection, and there are many kinds of connection methods such as clamps. Someone asked: what are the precautions for the use of rubber soft joints? Today, I'd like to introduce the precautions for rubber flexible joint of Jinan ventilation pipe.

　　通風管道橡膠軟接頭安裝時需要注意的事項有：

　　Matters needing attention during installation of rubber soft joint of ventilation pipe include:

　　1、橡膠接頭在初次承受壓力如安裝試壓等后或長期停用再次啟用前，應將螺栓重新加壓擰緊再投入運行橡膠伸縮器。

　　1、 After the rubber joint bears the pressure for the first time, such as installation and pressure test, or before it is put into use again after being stopped for a long time, the bolt shall be re pressurized and tightened before being put into operation.

　　2、當管道介質為酸，堿，油，高溫及其他特殊材料時應選用高于管道工作壓力一個擋位的橡膠接頭。

　　2. When the pipeline medium is acid, alkali, oil, high temperature and other special materials, the rubber joint with a gear higher than the working pressure of the pipeline shall be selected.

　　3、連接橡膠接頭的接口應是閥門法蘭或符合GB/T9115.1（RF）的法蘭。

　　3. The interface connecting rubber joint shall be valve flange or flange conforming to GB / t9115.1 (RF).

　　4、當管道產生瞬間壓力且大于工作壓力時應選用高于工作壓力一個擋位的接頭。

　　4. When the instantaneous pressure of the pipeline is greater than the working pressure, the joint with a gear higher than the working pressure shall be selected.

　　5、橡膠接頭正常使用介質溫度是0-60℃的普通水，特殊介質如：油、酸、堿、高溫及其他腐蝕性和質地堅硬的情況下，應選用相對應的橡膠接頭材質，不可盲目串用或通用。

　　5. The normal use medium temperature of rubber joint is 0-60 ℃ ordinary water. In case of special medium such as oil, acid, alkali, high temperature and other corrosive and hard conditions, the corresponding rubber joint material shall be selected, and it is not allowed to be used in series or in general.

　　6、高層給水或懸空給水，管道應固定在吊架，托架或錨架上，且不能讓接頭承受管道自身重量和軸向力，否則橡膠接頭應配備防拉脫裝置，并且其承受力大于管道軸向力。

　　6. For high-rise water supply or suspended water supply, the pipe shall be fixed on the hanger, bracket or anchor frame, and the joint shall not bear the weight and axial force of the pipe itself, otherwise the rubber joint shall be equipped with anti pulling device, and its bearing force shall be greater than the axial force of the pipe.

　　7、可曲撓橡膠接頭使用在水泵進出口時，應位于近水泵一側，與水泵之間應安裝金屬變徑接頭，且安裝在變徑的大口徑處。

　　7. When the flexible rubber joint is used at the inlet and outlet of the water pump, it shall be located at the side near the water pump, and a metal reducer joint shall be installed between the flexible rubber joint and the water pump, and it shall be installed at the large diameter of the reducer.

　　8、當管道位移量≥接頭的補償量時，應增加接頭的數量來平行位移量，嚴禁為了調整管道的超差，使接頭處于限的撓曲位移和偏差狀態，更不能超限度伸縮，位移，偏轉等。

　　8. When the displacement of the pipeline is equal to or greater than the compensation of the joint, the number of joints shall be increased to parallel the displacement. It is strictly prohibited to adjust the over tolerance of the pipeline, so that the joint is in the state of limited deflection displacement and deviation, not to mention the over tolerance expansion, displacement, deflection, etc.

　　9、安裝橡膠接頭時，螺栓的螺桿應伸向接頭外側，每一法蘭端面的螺栓按對角加壓的方法反復均勻擰緊，防止壓偏。絲扣接頭應使用標準扳手勻力擰緊，不要用加力桿加力使活接頭滑絲，滑棱，斷裂，而且要定期定時檢查，以免松動造成脫盤或滲水。

　　9. When installing the rubber joint, the screw of the bolt shall extend to the outside of the joint, and the bolt of each flange end face shall be tightened repeatedly and evenly according to the method of diagonal pressure to prevent the pressure deviation. Screw thread joint shall be tightened evenly with standard spanner. Do not force the flexible joint with force bar to make the sliding thread, sliding edge and fracture. Besides, regular and regular inspection shall be carried out to avoid disc breaking or water seepage caused by loosening.

　　10、使用或儲存橡膠接頭，應避免高溫，臭氧，油及酸堿環境，用在室外或向陽迎風的管道應搭建遮陽架，嚴禁曝曬，雨淋，風蝕。橡膠接頭表面嚴禁刷涂油漆和纏繞保溫材料，因橡膠接頭產品存在老化問題，應及時檢查更換。

　　10. When using or storing rubber joints, avoid high temperature, ozone, oil and acid-base environment. For outdoor or windward pipes, sunshade shall be set up. Exposure, rain and wind erosion are strictly prohibited. It is strictly prohibited to brush paint and wind insulation materials on the surface of rubber joint. Due to aging problems of rubber joint products, check and replace them in time.